[gull] Fwd: kernel 2.6.5 et usb

[Didier Donzé]

  Bonjour!

Je tourne sous debian sarge (upgrade de woody) et je suis passé au 
kernel 2.6.5. Seulement voilà, j'ai un problème usb que je n'arrive pas 
a résoudre, quand je plug in un peripherique usb, dmesg me donne ceci:
uhci_hcd 0000:00:07.2: port 2 portsc 0082
hub 1-0:1.0: port 2, status 100, change 1, 12 Mb/s
uhci_hcd 0000:00:07.2: port 2 portsc 0093
hub 1-0:1.0: port 2, status 101, change 1, 12 Mb/s
hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
hub 1-0:1.0: port 2 not reset yet, waiting 50ms
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not enabled, trying reset again...
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not enabled, trying reset again...
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not enabled, trying reset again...
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not enabled, trying reset again...
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not reset yet, waiting 200ms
hub 1-0:1.0: port 2 not enabled, trying reset again...
hub 1-0:1.0: Cannot enable port 2.  Maybe the USB cable is bad?

johnnybravo:~# cat /proc/bus/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.5 uhci_hcd
S:  Product=Intel Corp. 82371SB PIIX3 USB [Natoma/Triton II]
S:  SerialNumber=0000:00:07.2
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms


Il faut encore que je precise qu'avec le kernel 2.4.21 tout fonctionne 
normalement.. Qu'est ce que je peux faire? Quelqu'un a une idée, déjà eu 
le même problème?
Merci d'avance